Naphtha Hydrotreating Unit For Gasoline Production: A Complete Refinery Guide To Process Design, Reactor Engineering, Equipment Manufacturing, And Industrial Applications

Nov 03, 2026

Leave a message

Naphtha Hydrotreating Unit for Gasoline Production: A Complete Refinery Guide to Process Design, Reactor Engineering, Equipment Manufacturing, and Industrial Applications

1. Introduction: The Strategic Role of Naphtha Hydrotreating in Modern Refineries

In a modern oil refinery, producing high-quality gasoline requires much more than separating crude oil into different boiling-range fractions. Refinery operators must control sulfur, nitrogen, oxygen compounds, metals, olefins, and other contaminants while maintaining product yield, octane quality, catalyst activity, energy efficiency, and long-term operating reliability.

A Naphtha Hydrotreating Unit (NHT) is an important part of this integrated refining system. It uses hydrogen and a selected catalyst under controlled temperature and pressure to remove unwanted impurities from naphtha before the treated feed enters downstream processing units.

Its importance becomes clearer when the entire refinery process is considered. Naphtha hydrotreating is connected to crude distillation, catalytic reforming, light naphtha isomerization, gasoline blending, and refinery hydrogen management. It also belongs to a broader family of refinery hydrotreating processes that includes kerosene hydrotreating, diesel hydrotreating, gas oil hydrotreating, and residue upgrading.

Each hydrotreating unit has a different feedstock, process objective, catalyst system, operating severity, and equipment configuration. They should not be treated as interchangeable systems.

For example, a naphtha hydrotreater typically prepares feed for catalytic reforming or isomerization, while a diesel hydrotreater focuses on reducing sulfur and improving diesel product quality. A vacuum gas oil hydrotreater may prepare heavier feed for downstream catalytic cracking or hydrocracking.

For refinery owners, EPC contractors, process engineers, and equipment procurement teams, understanding these relationships is essential when planning a new gasoline production system, upgrading an existing refinery, or selecting high-pressure process equipment.

This guide examines the role of naphtha hydrotreating in gasoline production and the wider refinery process network. It also explains process chemistry, reactor design, equipment configuration, manufacturing challenges, and the engineering considerations involved in selecting a reliable equipment manufacturer.

3.jpg

2. Understanding the Position of Naphtha Hydrotreating in the Refinery Process

Crude oil contains hydrocarbons with a wide range of molecular structures and boiling points. A refinery first separates crude oil into different fractions and then converts or treats those fractions to meet product specifications.

A simplified refinery process arrangement may include:

Crude oil desalting and preheating

Atmospheric distillation

Vacuum distillation

Naphtha hydrotreating

Catalytic reforming

Light naphtha isomerization

Fluid catalytic cracking

Gasoline and diesel hydrotreating

Kerosene and jet fuel treatment

Gas recovery, sulfur recovery, hydrogen production, and product blending

The actual arrangement varies according to crude properties, refinery configuration, product demand, and available conversion technologies.

2.1 From crude distillation to naphtha treatment

The crude distillation unit separates crude oil into several fractions, including refinery gas, naphtha, kerosene, diesel-range material, atmospheric gas oil, and atmospheric residue.

Naphtha is generally recovered from the overhead or side-stream processing system of the atmospheric distillation unit. Its properties depend on the crude oil source and the refinery's fractionation configuration.

The naphtha stream may then be divided into light and heavy fractions.

Light naphtha commonly contains lower-boiling hydrocarbons and may be directed toward an isomerization unit after suitable pretreatment.

Heavy naphtha is often used as catalytic reformer feed after hydrotreating.

Mixed naphtha streams may require a treatment arrangement based on their combined composition.

Cracked naphtha from FCC or other conversion units may require a different treatment strategy.

The NHT unit therefore acts as an important connection between crude oil fractionation and downstream gasoline production.

2.2 Why untreated naphtha should not automatically enter downstream units

Untreated naphtha can contain sulfur compounds, nitrogen compounds, water, oxygen-containing components, and other contaminants.

These materials may interfere with downstream catalytic reactions.

For example, sulfur can poison or inhibit sensitive reforming catalysts. Nitrogen compounds can reduce catalyst activity and affect process stability. Water and other contaminants may also create operational problems in specific catalyst systems.

Hydrotreating reduces these contaminants and prepares the feed for the next processing stage.

The treatment target should be established using actual feed analysis and the downstream process licensor's requirements. A single generic sulfur specification is not sufficient for every refinery.

How To Increase Gasoline Octane Number From Naphtha: Process Design, Catalyst Selection And Equipment Manufacturing Guide

3. How Hydrotreating Units Work Across an Entire Refinery

Hydrotreating is not a single process applied to all petroleum fractions. It is a family of catalytic processes designed to treat different refinery streams using hydrogen.

The major objectives are generally to remove sulfur, nitrogen, oxygen, and selected metal contaminants, and to improve the quality or processability of the feedstock.

Different refinery fractions require different treatment conditions.

3.1 Naphtha hydrotreating: Preparing feed for gasoline production

Naphtha hydrotreating is primarily used to prepare suitable naphtha feed for catalytic reforming, isomerization, or other downstream processing.

Its main functions include:

Removing sulfur compounds

Reducing nitrogen compounds

Removing or converting selected oxygen compounds

Saturating undesirable olefins where required

Protecting downstream catalysts

Improving feed stability

The treated naphtha can then enter the appropriate gasoline production route.

3.2 Kerosene hydrotreating: Producing cleaner kerosene and jet fuel components

Kerosene hydrotreating treats kerosene-range hydrocarbons to reduce sulfur and other impurities and to meet relevant product quality requirements.

Depending on the feed and target product, the process may also improve properties such as smoke point, color, and storage stability.

In refineries producing aviation turbine fuel, kerosene treatment must be coordinated with the applicable jet fuel specifications and the refinery's product certification system.

Important equipment may include:

Kerosene hydrotreater reactor

Feed/effluent heat exchanger

Charge heater

High-pressure separator

Recycle gas compressor

Product stripper

Air cooler and process cooler

The reactor metallurgy and operating conditions depend on the feed composition, hydrogen partial pressure, process severity, and applicable design requirements.

3.3 Diesel hydrotreating: Producing low-sulfur diesel

Diesel hydrotreating is one of the most important refining processes for meeting modern transportation fuel requirements.

Diesel-range feed may come from atmospheric distillation, catalytic cracking, coking, or other refinery conversion processes.

A diesel hydrotreater uses hydrogen and a suitable catalyst to reduce sulfur and, depending on the process configuration, nitrogen and aromatic compounds.

Its main objectives may include:

Producing ultra-low-sulfur diesel

Improving diesel product stability

Reducing sulfur emissions associated with fuel use

Preparing feed for downstream processing

Meeting regional diesel specifications

Diesel hydrotreating often requires different operating conditions and catalyst systems from naphtha hydrotreating because diesel feed contains heavier molecules and different sulfur compound distributions.

The design of the reactor, hydrogen circulation system, and heat recovery equipment must reflect these differences.

3.4 Vacuum gas oil hydrotreating: Preparing heavier feed for conversion

Vacuum gas oil (VGO) is obtained from vacuum distillation and is an important feedstock for downstream conversion processes.

Depending on the refinery configuration, VGO may be sent to fluid catalytic cracking, hydrocracking, or other upgrading processes.

VGO hydrotreating can reduce sulfur, nitrogen, and selected contaminants before the feed enters a downstream conversion unit.

The benefits may include:

Lower sulfur loading in downstream products

Improved FCC feed quality

Reduced catalyst contamination

Better downstream process stability

Improved integration with refinery emissions-control objectives

A VGO hydrotreater typically operates under more demanding conditions than a conventional naphtha hydrotreater. Its equipment may require larger pressure vessels, higher design pressures, specialized materials, and more complex reactor internals.

3.5 Residue hydrotreating: Supporting heavy oil upgrading

Atmospheric and vacuum residues contain heavier hydrocarbons, asphaltenes, metals, sulfur, and other contaminants.

Residue hydrotreating processes are designed to upgrade these heavy streams before further conversion or blending.

Depending on the process technology, residue treatment may use fixed-bed, ebullated-bed, or other reactor configurations.

Typical objectives include:

Reducing sulfur

Removing selected metals

Reducing nitrogen

Improving downstream conversion performance

Preparing residue for further upgrading

Supporting refinery bottom-of-the-barrel processing

Residue service presents demanding engineering challenges because of high viscosity, catalyst fouling, metal deposition, coke formation, and severe operating conditions.

The reactor configuration and mechanical design must be developed specifically for the selected technology.

3.6 FCC gasoline selective hydrotreating: Balancing sulfur removal and octane retention

FCC gasoline is an important contributor to the refinery gasoline pool. It can contain significant sulfur and olefin concentrations.

Unlike conventional straight-run naphtha pretreatment, FCC gasoline treatment must often balance sulfur removal against the preservation of valuable olefins.

Severe hydrogenation can saturate olefins and reduce octane. Therefore, selective hydrodesulfurization processes may be used to reduce sulfur while limiting undesirable olefin saturation.

Depending on the refinery configuration, the treatment route may include:

FCC gasoline fractionation

Selective hydrodesulfurization

Hydrogenation reactor

Interstage separation

Product stabilization

Gasoline blending

This is an important distinction for engineering and procurement teams: a conventional naphtha hydrotreater should not automatically be considered suitable for FCC gasoline selective desulfurization.

3.7 The relationship between hydrotreating and hydrogen production

Hydrogen is a key utility and reactant throughout the refinery.

Naphtha hydrotreating, diesel hydrotreating, kerosene hydrotreating, VGO hydrotreating, and other hydrogen-consuming processes all place demands on the refinery hydrogen network.

Hydrogen is commonly produced through steam methane reforming or other hydrogen-production technologies, depending on the refinery configuration.

A refinery hydrogen balance must consider:

Hydrogen production capacity

Hydrogen purity

Hydrogen consumption by individual units

Recycle gas recovery

Purge gas losses

Hydrogen distribution pressure

Future expansion requirements

A new hydrotreating unit may affect the hydrogen availability of existing units. Consequently, the hydrogen network should be evaluated as part of the overall refinery project rather than treating each hydrotreater as an isolated installation.

4. The Relationship Between Naphtha Hydrotreating and Gasoline Production Units

The most important downstream relationship for gasoline-oriented naphtha hydrotreating is its connection to catalytic reforming and isomerization.

4.1 Naphtha hydrotreating before catalytic reforming

Catalytic reforming converts suitable naphtha components into higher-octane products through reactions such as dehydrogenation, dehydrocyclization, and isomerization.

The reforming process can produce high-octane reformate and hydrogen-rich gas.

However, reforming catalysts, especially platinum-based catalyst systems, are sensitive to contaminants.

Sulfur and nitrogen compounds can significantly affect catalyst performance. For this reason, heavy naphtha is normally treated before entering the reforming unit.

A typical process sequence is:

Crude distillation → Naphtha fractionation → Naphtha hydrotreating → Catalytic reforming → Reformate stabilization → Gasoline blending

The NHT unit does not directly perform the octane-improvement reactions associated with catalytic reforming. Its role is to prepare a suitable feed and protect the downstream catalyst.

4.2 Naphtha hydrotreating before isomerization

Light naphtha may contain normal paraffins that can be converted into branched isomers with higher octane values.

The isomerization process can use different catalyst systems, including chloride-based or molecular-sieve-based technologies.

These catalysts have different sensitivities to sulfur, water, nitrogen, and other contaminants.

Pretreatment requirements therefore depend on the selected isomerization technology.

A typical arrangement is:

Light naphtha fractionation → Feed pretreatment → Isomerization → Product stabilization → Gasoline blending

The pretreatment section may include hydrotreating, drying, and other purification steps as required by the process technology.

4.3 Hydrotreating and gasoline blending optimization

A refinery gasoline pool may contain several blending components:

Catalytic reformate

Isomerate

FCC gasoline

Alkylate, where available

Hydrocracked gasoline

Other suitable refinery gasoline streams

Each component contributes different properties, including octane, vapor pressure, sulfur, aromatics, olefins, and distillation characteristics.

Hydrotreating influences the final gasoline pool by controlling the sulfur and other contaminants in selected blending components.

However, it also affects component yield and composition. For example, olefin saturation may reduce octane in some streams.

Therefore, the NHT process should be evaluated in relation to the refinery's overall gasoline blending strategy rather than solely by its outlet sulfur concentration.

5. Main Process Configuration of a Naphtha Hydrotreating Unit

A conventional naphtha hydrotreater can be divided into several interconnected process sections.

The exact arrangement depends on feed composition, capacity, operating conditions, catalyst technology, and downstream product requirements.

5.1 Feed receiving and pretreatment section

Naphtha enters the unit through a feed system and is normally collected in a feed surge drum or buffer vessel.

The section may include:

Feed surge drum

Charge pumps

Feed filters or strainers

Feed flow control system

Sampling connections

Feed/effluent heat exchangers

Hydrogen mixing facilities

The feed surge drum helps stabilize the liquid supply and reduces the influence of upstream process fluctuations.

Filtration is important when the feed contains suspended solids, corrosion products, catalyst fines, or other contaminants that may cause plugging or increase pressure drop.

5.2 Hydrogen mixing and feed heating section

Hydrogen-rich recycle gas and makeup hydrogen are combined with the hydrocarbon feed at designated mixing points.

The combined stream is preheated through a feed/effluent heat exchanger before entering the charge heater.

Heat integration reduces the duty required from the fired heater and can improve overall energy efficiency.

The exchanger must nevertheless be designed for:

Fouling potential

Thermal expansion

Pressure drop limitations

Startup and shutdown conditions

Mechanical cleaning requirements

Inspection and maintenance access

5.3 High-pressure catalytic reactor section

The reactor is the central process vessel in the NHT system.

The heated mixture of naphtha and hydrogen enters the reactor and passes through catalyst beds. Under controlled conditions, sulfur and other undesirable compounds react with hydrogen.

A typical reactor may contain:

Inlet distributor

Gas-liquid distribution components

Catalyst support grid

Catalyst bed

Inert or grading material, where specified

Bed support and retention structures

Thermowells and temperature measurement points

Quench facilities, where required

Outlet collection system

The reactor internals must be coordinated with the selected catalyst system and process technology.

Poor distribution can result in uneven flow, localized overheating, incomplete treatment, premature catalyst deactivation, and excessive pressure drop.

5.4 High-pressure separation and recycle hydrogen section

After leaving the reactor, the hot effluent is cooled through heat recovery and cooling equipment before entering the high-pressure separator.

The separator divides the reactor effluent into gas and liquid phases.

The gas phase contains hydrogen together with light hydrocarbons and reaction products such as hydrogen sulfide. Depending on the process configuration, it may pass through gas treatment before being returned to the reactor through a recycle gas compressor.

The liquid phase proceeds to downstream stabilization or stripping.

Important equipment includes:

High-pressure separator

Recycle gas compressor

Compressor suction knockout drum

Gas cooling equipment

Recycle gas piping

Hydrogen makeup system

Gas treatment equipment, where required

5.5 Product stripping and stabilization section

The liquid hydrocarbon leaving the high-pressure separation section contains dissolved gases and reaction products.

A stripper or stabilizer removes unwanted light components and dissolved gases to produce a suitable treated naphtha stream.

This section may include:

Stripper column

Reboiler

Overhead condenser

Reflux drum

Reflux pumps

Product cooler

Treated naphtha pumps

The treated naphtha is then routed to catalytic reforming, isomerization, or other downstream processing facilities according to its boiling range and product requirements.

6. Critical Chemical Engineering Considerations

A successful NHT design begins with a reliable process design basis. Selecting equipment before establishing feed properties and operating cases creates unnecessary risks during detailed engineering and commissioning.

6.1 Feed composition and variability

Feed characterization should include:

Initial and final boiling points

Density and API gravity

Total sulfur and sulfur compound distribution

Total nitrogen

Olefin and diolefin content

Aromatic content

Bromine number, where relevant

Silicon, arsenic, and other catalyst poisons where relevant

Water and sediment

Distillation curve

Feed flow rate and expected variability

A design based only on average sulfur content may be insufficient.

A refinery blending straight-run and cracked naphtha, for example, may experience changes in olefin concentration, sulfur species, and fouling tendency as the blending ratio changes.

The design should evaluate normal feed, maximum contaminant feed, minimum throughput, and expected future feed changes.

6.2 Catalyst selection and bed configuration

Naphtha hydrotreating commonly uses supported non-noble-metal catalysts, with cobalt-molybdenum and nickel-molybdenum systems being established options.

The correct catalyst depends on:

Sulfur-removal target

Nitrogen concentration

Feed olefin content

Required hydrogenation activity

Operating temperature and pressure

Expected catalyst cycle length

Contaminant profile

A grading or guard-bed arrangement may be needed where feed contaminants or fouling tendencies justify additional protection.

Catalyst suppliers may specify different particle sizes, loading methods, support materials, and bed arrangements. These requirements directly affect reactor internal design.

6.3 Temperature, pressure, and hydrogen partial pressure

Hydrotreating performance is influenced by several interacting variables.

Reactor temperature: Higher temperature can improve reaction rates, but excessive severity may accelerate catalyst deactivation or cause undesirable hydrogenation.

Operating pressure: Pressure influences hydrogen availability and reaction equilibrium.

Hydrogen partial pressure: This is more meaningful than total reactor pressure alone. Gas composition and hydrocarbon vapor pressure influence the available hydrogen partial pressure.

Liquid hourly space velocity: LHSV affects the contact time available for reactions.

Hydrogen-to-oil ratio: This affects hydrogen availability, gas circulation, heat transfer, and reactor hydraulic performance.

These variables must be optimized together.

6.4 Reaction heat and temperature control

Hydrotreating reactions are generally exothermic. Reactor temperature can therefore increase as the feed passes through the catalyst bed.

The design should evaluate:

Reactor inlet temperature

Expected temperature rise

Maximum catalyst-bed temperature

Temperature profile along the reactor

Potential local hot spots

Need for inter-bed quench

Startup and upset conditions

A single catalyst bed may be suitable for some relatively mild naphtha hydrotreating services. Other configurations may require multiple beds or additional temperature-control arrangements.

6.5 Hydrogen consumption and recycle gas quality

A complete hydrogen balance should distinguish:

Chemical hydrogen consumption

Hydrogen dissolved in liquid products

Hydrogen lost with purge gas

Hydrogen recovered and recycled

Hydrogen entering with makeup gas

Hydrogen purity and contaminant accumulation

The recycle gas system must maintain suitable hydrogen partial pressure while controlling the buildup of light hydrocarbons, hydrogen sulfide, and other impurities.

7. Engineering Design Details That Determine Long-Term Performance

7.1 Reactor diameter and catalyst-bed hydraulics

Reactor diameter is determined by more than the required catalyst volume.

The engineering evaluation should consider catalyst volume, liquid and gas flow rates, superficial velocity, gas-liquid distribution, pressure drop, catalyst particle characteristics, operating turndown, future capacity allowance, and transportation limits.

The final diameter must be established through process hydraulic calculations and mechanical design.

7.2 Feed distributor and liquid distribution

Uneven liquid distribution is one of the most important causes of poor fixed-bed reactor performance.

A suitable inlet distribution system should minimize localized flow concentration and distribute the gas-liquid mixture across the catalyst bed.

Depending on the process configuration, the design may incorporate inlet diverters, distributor trays, spray or mixing devices, gas-liquid distribution elements, and catalyst bed support structures.

Turndown performance is particularly important. A distributor that works well at full load may perform poorly at reduced throughput.

7.3 Reactor internals and maintainability

Reactor internals operate in a demanding environment involving hydrogen, hydrocarbons, elevated temperatures, and potentially corrosive reaction products.

The internal design should address mechanical strength, thermal expansion, corrosion resistance, vibration, catalyst retention, inspection access, installation sequence, and removal requirements.

7.4 Feed/effluent exchanger design

The feed/effluent exchanger recovers heat from reactor effluent and transfers it to incoming feed.

Its performance affects fired heater duty, fuel consumption, unit energy efficiency, reactor inlet temperature stability, and cooling system load.

Mechanical design should evaluate differential pressure, tube-to-tubesheet joints, thermal expansion, vibration, fouling, and inspection requirements.

7.5 High-pressure separator design

The high-pressure separator influences hydrogen recovery, recycle compressor reliability, and the amount of gas carried into downstream liquid processing.

Key considerations include gas and liquid flow rates, gas-liquid disengagement, liquid residence time, inlet momentum control, mist elimination, level control, pressure control, drainage, and inspection access.

7.6 Stripper column and overhead system

The stripper removes dissolved hydrogen sulfide and light components from treated naphtha.

Its design depends on product specification, feed composition, pressure, available steam or reboiler utility, and condenser operating conditions.

The overhead system deserves particular attention because hydrogen sulfide, ammonia, water, and other components may create corrosion or deposition risks depending on process chemistry.

8. Main Equipment Required for a Naphtha Hydrotreating Unit

Equipment Main function Important engineering considerations
Feed surge drum Stabilizes feed supply Capacity, level control, phase separation
Charge pump Delivers feed to the high-pressure system Differential pressure, NPSH, seal arrangement
Feed/effluent exchanger Recovers process heat Thermal duty, pressure drop, fouling
Charge heater Raises feed temperature Heat duty, tube design, burner control
Naphtha hydrotreater reactor Performs catalytic reactions Pressure boundary, catalyst volume, internals
High-pressure separator Separates recycle gas and liquid Gas-liquid separation, mist elimination
Recycle gas compressor Circulates hydrogen-rich gas Gas composition, flow, pressure ratio
Product stripper Removes dissolved gases and light components Column hydraulics, reboiler duty
Reboiler and condenser Supplies and removes process heat Thermal performance, corrosion
Pumps and coolers Transfer and condition process streams Materials, sealing, hydraulic performance

9. Manufacturing Challenges of High-Pressure Naphtha Hydrotreating Equipment

The reliability of a hydrotreating unit depends not only on process design but also on the quality of its pressure equipment.

9.1 Material selection and traceability

Material selection must follow approved design conditions, applicable construction codes, process chemistry, corrosion assessment, and client specifications.

The material evaluation may include:

Design pressure and temperature

Hydrogen partial pressure

Hydrogen sulfide concentration

Wet sour-service conditions

Corrosion allowance

Minimum design metal temperature

Mechanical properties

Weldability

Heat-treatment requirements

Hydrogen service requires particular care. Depending on temperature, hydrogen partial pressure, and material chemistry, high-temperature hydrogen attack may need to be evaluated using the applicable industry methodology.

Where wet hydrogen sulfide conditions exist, the design may also need to address relevant forms of wet H₂S damage and material hardness restrictions.

Material traceability should be maintained from incoming inspection through cutting, forming, welding, heat treatment, and final assembly.

9.2 Heavy plate rolling and forming

Large reactor shells and high-pressure separator vessels may require thick plate rolling and accurately controlled forming operations.

Manufacturing challenges include plate dimensional inspection, edge preparation, rolling accuracy, shell roundness, longitudinal seam alignment, circumferential joint fit-up, nozzle opening preparation, and dimensional control after welding.

For thick-wall vessels, forming and welding shrinkage can affect final geometry.

9.3 Pressure-vessel welding

Welding quality is one of the most important factors influencing the structural integrity of high-pressure equipment.

The welding procedure should be qualified for the selected materials, thickness range, joint configuration, and applicable construction code.

Important manufacturing controls include:

Approved welding procedure specifications

Qualified welding procedure records

Welder qualification

Welding consumable control

Preheating, where required

Interpass temperature control

Heat input control

Weld sequence planning

Post-weld heat treatment, where required

For heavy-wall equipment, welding sequence and distortion control require careful planning.

9.4 Non-destructive examination

Depending on the applicable code, design category, material, and client specification, inspection may include:

Radiographic testing (RT)

Ultrasonic testing (UT)

Magnetic particle testing (MT)

Liquid penetrant testing (PT)

Visual examination (VT)

Hardness testing

Positive material identification (PMI), where specified

The inspection plan should identify the examination method, examination extent, acceptance criteria, and inspection hold points.

9.5 Post-weld heat treatment and dimensional stability

PWHT may be required depending on material, thickness, construction code, and service conditions.

For thick-wall pressure vessels, the heat-treatment procedure must control heating rate, soaking temperature, holding time, and cooling rate.

Temperature monitoring should be properly distributed to ensure that the vessel receives the specified thermal treatment.

9.6 Pressure testing and final inspection

Hydrostatic testing is commonly used to verify pressure-boundary integrity in accordance with the applicable construction code and approved procedure.

The final manufacturing dossier should include material certificates, welding records, NDE reports, heat-treatment charts, pressure-test records, dimensional inspection reports, and other documents required by the contract.

10. Design Codes, Standards, and Quality Assurance

The applicable design and manufacturing standards depend on equipment category, project location, client specifications, and regulatory requirements.

Commonly referenced standards may include:

ASME Boiler and Pressure Vessel Code Section VIII for applicable pressure vessels

ASME Section II for material requirements

ASME Section V for non-destructive examination

ASME Section IX for welding and brazing qualifications

API standards where applicable to refinery equipment

TEMA standards for relevant shell-and-tube heat exchangers

Applicable piping codes for process and utility piping

Relevant sour-service material requirements, where applicable

Not every standard applies to every item. The project specification must define the governing code and resolve any conflicts between client standards, local regulations, and international codes.

A manufacturer's pressure-vessel design or manufacturing qualification does not automatically establish authorization to manufacture every category of process equipment under every international code. For example, pressure-vessel manufacturing qualifications should not be presented as equivalent to ASME certification unless the relevant certification is actually held and applicable to the equipment.

11. How Hydrotreating Supports the Entire Refinery Production System

The value of hydrotreating becomes clearer when the entire refinery is considered as an interconnected production network.

11.1 Supporting crude oil processing

Crude distillation separates the incoming crude into fractions, but the resulting streams do not necessarily meet the requirements of downstream catalytic units or finished products.

Hydrotreating helps convert these intermediate streams into cleaner, more suitable feedstocks.

For example, naphtha from atmospheric distillation may require treatment before reforming, while heavier gas oil streams may require treatment before catalytic cracking or hydrocracking.

11.2 Protecting downstream catalysts

Many refinery conversion processes depend on catalysts with carefully controlled activity and selectivity.

Contaminants in the feed can reduce catalyst performance, increase operating costs, and shorten catalyst cycle length.

Hydrotreating reduces selected contaminants before the feed enters these downstream processes.

The benefit is not limited to product sulfur reduction. It can also include improved catalyst protection, better process stability, and more predictable operating performance.

11.3 Improving refinery product quality

Different hydrotreating units contribute to the quality of different refinery products:

Naphtha hydrotreating supports reformer and isomerization feed quality.

Diesel hydrotreating helps meet low-sulfur diesel specifications.

Kerosene hydrotreating supports kerosene and aviation fuel quality requirements.

Gas oil hydrotreating improves feed quality for downstream conversion.

Selective FCC gasoline hydrotreating helps reduce gasoline sulfur while managing octane retention.

Residue hydrotreating supports heavy oil upgrading.

The final product quality depends on the complete process route, blending strategy, and applicable product standards.

11.4 Improving refinery flexibility

A refinery may need to process different crude oils or adjust its product slate as market demand changes.

The ability to treat different feedstocks can improve operating flexibility, but only when the process and equipment have been designed for the expected feed range.

A new hydrotreating unit or an existing-unit revamp may allow the refinery to handle higher-sulfur feeds, protect downstream catalysts, or improve product quality.

11.5 Integrating hydrogen, fuel gas, and sulfur recovery systems

Hydrotreating units are closely connected to the refinery hydrogen network and sulfur management system.

Hydrogen-rich recycle gas is recovered and circulated, while purge gas may be routed to an appropriate refinery gas system.

Hydrogen sulfide generated by hydrotreating may be directed to amine treating and sulfur recovery facilities, depending on the refinery configuration.

This integration means that a new NHT project can affect:

Hydrogen production and distribution

Recycle gas compression

Amine treating capacity

Sour water handling

Sulfur recovery capacity

Fuel gas balance

Flare and relief systems

These interfaces should be reviewed during the project feasibility and basic engineering stages.

11.6 Supporting refinery revamp and expansion projects

Existing refineries may need to increase capacity, improve product specifications, change crude feed, or replace aging equipment.

Hydrotreating systems are often included in such modernization projects.

Typical project scopes may involve:

New naphtha hydrotreater installation

NHT reactor replacement

High-pressure separator replacement

Feed/effluent exchanger revamp

Recycle gas system modification

Diesel hydrotreater capacity expansion

Kerosene hydrotreater modernization

VGO pretreatment project

Hydrogen network expansion

For these projects, equipment manufacturers must consider not only new equipment design but also existing plant dimensions, foundation capacity, lifting access, tie-in locations, shutdown windows, and transportation restrictions.

12. Industrial Applications of Naphtha Hydrotreating Units

12.1 Straight-run naphtha pretreatment

This is a common application in refineries with catalytic reforming and isomerization facilities.

The objective is to remove contaminants from naphtha produced by crude distillation before it enters downstream conversion units.

12.2 Heavy naphtha hydrotreating for catalytic reforming

Heavy naphtha is treated to reduce catalyst poisons before entering the reformer.

The treated feed supports the production of high-octane reformate, which is an important gasoline blending component.

12.3 Light naphtha hydrotreating for isomerization

Light naphtha pretreatment helps protect the selected isomerization catalyst.

The treated stream is subsequently converted into higher-octane isomerate, subject to the process technology and feed composition.

12.4 Mixed naphtha treatment

Refineries that combine naphtha from different sources need to evaluate the full feed composition and operating range.

The NHT configuration should reflect expected changes in sulfur, nitrogen, olefins, and other contaminants.

12.5 Refinery gasoline quality improvement

Naphtha hydrotreating contributes to the refinery gasoline production system by preparing feed for reforming and isomerization.

When combined with appropriate FCC gasoline treatment and gasoline blending control, it supports the production of gasoline that meets applicable sulfur, octane, and other quality requirements.

13. Common Engineering Mistakes in NHT Projects

Mistake 1: Selecting equipment before confirming the feed assay

Feed composition determines reaction severity, catalyst selection, hydrogen demand, and equipment duty.

Mistake 2: Treating every naphtha stream as the same feedstock

Straight-run naphtha, coker naphtha, and FCC naphtha have different properties and may require different treatment strategies.

Mistake 3: Focusing only on total reactor pressure

Hydrogen partial pressure, gas composition, recycle flow, and contaminant accumulation must also be evaluated.

Mistake 4: Ignoring reactor internals

A pressure vessel may meet its mechanical design requirements while poor internal distribution still causes catalyst maldistribution and operational problems.

Mistake 5: Maximizing heat recovery without considering maintenance

High heat-transfer efficiency is valuable, but exchanger fouling, cleaning access, pressure drop, and tube leakage risks must also be considered.

Mistake 6: Ignoring refinery-wide hydrogen and sulfur balances

A new hydrotreater consumes hydrogen and produces hydrogen sulfide. The impact on hydrogen production, recycle gas systems, amine treating, sour water, and sulfur recovery must be evaluated.

Mistake 7: Confusing hydrotreating with gasoline conversion

Hydrotreating prepares and purifies the feed. Catalytic reforming and isomerization perform different conversion functions. Selective FCC gasoline desulfurization also requires its own process evaluation.

14. How to Select a Reliable Naphtha Hydrotreating Equipment Manufacturer

For an EPC contractor or refinery owner, equipment selection should consider the manufacturer's ability to understand process requirements and translate them into a practical fabrication package.

Engineering coordination

Can the manufacturer work with approved process data, equipment specifications, mechanical design conditions, nozzle orientation, and project interface requirements?

Can the engineering team identify conflicts between process requirements and fabrication limitations before manufacturing begins?

Pressure-vessel manufacturing capability

Can the workshop handle the required shell diameter, plate thickness, vessel length, lifting weight, and welding configuration?

Are suitable forming, welding, heat-treatment, and inspection facilities available?

Quality control

Does the manufacturer maintain material traceability, qualified welding procedures, qualified welders, NDE capability, and documented inspection procedures?

Can the manufacturer provide a complete manufacturing dossier?

Project coordination

Can the manufacturer coordinate equipment dimensions, transport limitations, lifting points, foundations, piping interfaces, and installation requirements with the EPC team?

Lifecycle considerations

Does the design provide practical access for inspection, catalyst loading and unloading, internal maintenance, and future repairs?

The lowest initial purchase price is not necessarily the lowest lifecycle cost. Equipment reliability, manufacturing consistency, and maintainability directly influence refinery operating economics.

15. GYRO's Manufacturing Strength for Naphtha Hydrotreating Equipment

For a naphtha hydrotreating project, the pressure equipment must be manufactured with careful attention to mechanical design, material traceability, welding quality, dimensional control, inspection, and delivery documentation.

ZIBO GYRO INDUSTRY ENGINEERING (GYRO) provides chemical and petrochemical equipment engineering and manufacturing services, with capabilities relevant to pressure vessels, reactors, heat exchangers, towers, and customized process equipment.

GYRO's integrated engineering and manufacturing approach helps coordinate equipment design requirements with actual workshop production conditions.

15.1 Pressure-vessel design and manufacturing

GYRO's published company qualifications include A2-level pressure-vessel design and manufacturing qualifications.

This capability is relevant to project scopes involving applicable pressure vessels and process equipment. The final equipment category, design code, pressure and temperature conditions, and regulatory requirements must be checked against the actual project specification and applicable qualification scope.

Potential equipment scopes for technical evaluation include:

Naphtha hydrotreating reactor vessels

High-pressure separator vessels

Feed surge drums

Recycle gas knockout drums

Process heat exchangers

Product stripping columns

Reboilers and other pressure equipment

The final manufacturing scope should be confirmed against approved drawings, design calculations, material requirements, and contractual responsibilities.

15.2 Manufacturing facilities and production resources

GYRO's published manufacturing information describes a production site of approximately 30,000 m², including around 20,000 m² of workshop area.

The company reports more than 150 manufacturing and processing machines, annual design and manufacturing capacity exceeding 8,000 tonnes, and a maximum plate-rolling capability of 80 mm thickness by 3,000 mm width.

These resources provide a manufacturing foundation for a range of chemical and petrochemical equipment.

For individual high-pressure reactor projects, feasibility must still be evaluated against vessel diameter, total weight, material grade, wall thickness, welding requirements, heat-treatment envelope, inspection requirements, and transportation limitations.

15.3 Welding and inspection capability

GYRO's published information identifies 14 qualified pressure-vessel welders covering 36 welding qualification items, together with four NDT personnel covering RT, UT, MT, and PT inspection methods.

For a hydrotreating reactor or separator project, these resources can support the manufacturing quality-control process, subject to the applicable qualification range, approved inspection plan, and project-specific requirements.

15.4 Engineering and manufacturing integration

One practical advantage of integrated engineering and manufacturing is the ability to review fabrication considerations early.

For example:

Shell and head forming can be evaluated against workshop capacity.

Nozzle locations can be checked against welding and inspection access.

Internal support structures can be coordinated with installation requirements.

Lifting arrangements can be reviewed before final assembly.

Manufacturing tolerances can be considered during equipment layout development.

This coordination helps reduce avoidable design changes and improves communication between engineering, procurement, and manufacturing teams.

15.5 A practical manufacturing partner for refinery projects

GYRO understands that refinery equipment is not purchased only for its appearance on a general arrangement drawing. It must fit the process, meet the specified mechanical requirements, pass inspection, arrive safely at the project site, and remain maintainable during operation.

For EPC contractors and refinery owners, equipment discussions should begin with actual operating conditions and approved specifications rather than a generic product description.

GYRO can evaluate applicable pressure-vessel, reactor, heat-exchanger, separator, and tower manufacturing scopes based on project requirements.

Process technology licensing, catalyst guarantees, rotating machinery packages, and complete NHT performance guarantees must be separately defined with the responsible technology provider or package contractor.

16. What Information Is Needed to Start an NHT Equipment Inquiry?

To evaluate a naphtha hydrotreating equipment package, the following information is useful.

Process information

Feed type and source

Feed capacity

Feed composition and assay

Total sulfur and nitrogen

Olefin and aromatic content

Required treated-product specifications

Hydrogen purity and availability

Operating temperature and pressure

Mechanical information

Design pressure and temperature

Equipment dimensions or preliminary sizing

Material requirements

Corrosion allowance

Applicable construction code

Corrosion and sour-service requirements

Design life

NDE and PWHT requirements

Project information

Project location

Applicable local regulations

Required delivery schedule

Transportation limitations

Inspection and certification requirements

Required engineering documents

Battery limits and supply scope

Even preliminary process data can help establish whether a proposed reactor or pressure-vessel configuration is technically suitable for further evaluation.

17. Frequently Asked Questions About Naphtha Hydrotreating Units

What is the main purpose of a naphtha hydrotreating unit?

Its main purpose is to remove sulfur, nitrogen, oxygen compounds, and selected contaminants from naphtha using hydrogen and a suitable catalyst. The treated stream is then suitable for downstream processing or blending, depending on its quality and the refinery configuration.

What is the role of hydrotreating in an entire refinery?

Hydrotreating improves the quality of intermediate refinery streams and protects downstream catalysts. Different units treat naphtha, kerosene, diesel, gas oil, and residue to meet different process and product requirements.

Does a naphtha hydrotreater directly increase gasoline octane?

Not normally. Conventional hydrotreating primarily purifies the feed. It may saturate olefins and reduce octane under some conditions. Higher-octane gasoline components are typically produced through downstream processes such as catalytic reforming and isomerization.

What is the difference between naphtha hydrotreating and catalytic reforming?

Naphtha hydrotreating removes impurities and protects downstream catalysts. Catalytic reforming changes the molecular structure of suitable naphtha components to produce high-octane reformate and hydrogen-rich gas.

Is a naphtha hydrotreater the same as a diesel hydrotreater?

No. Both use hydrogen and catalysts, but their feedstocks, operating conditions, catalyst systems, reactor configurations, and product targets are different.

Why does a refinery need a hydrogen network study before installing a new hydrotreater?

A new hydrotreater increases hydrogen demand and may affect hydrogen availability across existing refinery units. The project should evaluate hydrogen production, purity, pressure, recycle gas recovery, purge losses, and the capacity of associated gas treatment facilities.

Can one naphtha hydrotreating unit process different types of naphtha?

Potentially, but the feed range must be included in the original design basis or evaluated through a revamp study. Different naphtha sources may contain substantially different sulfur compounds, olefins, nitrogen, metals, and fouling precursors.

Can GYRO manufacture a naphtha hydrotreating reactor?

GYRO's published A2 pressure-vessel qualifications and manufacturing capabilities provide a basis for evaluating applicable reactor and pressure-vessel manufacturing scopes. Final acceptance depends on the project's equipment category, design code, material, dimensions, service conditions, and regulatory requirements.

18. Conclusion: Integrating Process Engineering and Equipment Manufacturing for Better Refinery Performance

Naphtha hydrotreating is an important part of modern gasoline production, but its value extends beyond a single reactor or process unit.

It connects crude distillation with catalytic reforming and isomerization, supports gasoline quality management, protects downstream catalysts, and forms part of the refinery's wider hydrogen and sulfur management systems.

At the same time, other hydrotreating units perform equally important roles across the refinery by treating kerosene, diesel, gas oil, cracked gasoline, and heavy residue streams. Each unit must be designed around its own feed characteristics, process objectives, catalyst requirements, operating conditions, and mechanical design basis.

For a successful project, process design, equipment configuration, material selection, pressure-vessel engineering, manufacturing quality, inspection, and refinery-wide utility integration must be considered together.

GYRO welcomes technical discussions with refinery owners, EPC contractors, process engineering companies, and equipment procurement teams seeking pressure vessels, hydrotreating reactors, heat exchangers, separators, columns, and customized petrochemical equipment.

If your project involves a new naphtha hydrotreating unit, a refinery-wide hydrotreating expansion, an existing-unit revamp, or the replacement of critical pressure equipment, share your preliminary process data and equipment specifications with our engineering team.

Send Inquiry
Send Inquiry